Day 22 Back to Exams Page 1. Looking at the below output. What command will allow EIGRP to load balance across the two routes? R2(config-router)#variance 6R2(config-router)#variance 2R2(config-router)#variance 3R2(config-router)#variance 5Question 1 of 18 2. Hello packets sent by EIGRP do not require an Acknowledgment to be sent confirming that they were received.TrueFalseQuestion 2 of 18 3. Looking at the fig below. The route from R1-R2-R5 will be? None of the above and the route will be set to null 0.Neither a successor or feasible successor route but placed in the topology table.A feasible successor route placed in the routing table.A successor route placed in the routing table.Question 3 of 18 4. Which K values are used in EIGRP metric calculation? Choose all that apply.K1K3K5K2K4Question 4 of 18 5. Convergence time for EIGRP is much slower than other distance vector protocols due to it's complicated algorithm.TrueFalseQuestion 5 of 18 6. Looking at the fig below, the path from R1-R4-R5 will be? A successor route placed in the routing table.A feasible successor route placed in the routing table.A feasible successor route placed in the topology table.A successor route placed in the topology table.Question 6 of 18 7. You configure the below on the router using EIGRP. What will the router show in the 'show ip protocols' output. 10.1.1.0 0.0.0.25510.0.0.010.1.1.0/2410.1.1.0/8Question 7 of 18 8. EIGRP default values for the K values are K1 = K3 =1 and K2 = K4 = K5 = 0. If changed on one router or switch, then these values must be adjusted for all other routers or switches within the autonomous system.TrueFalseQuestion 8 of 18 9. Any other routes to the same destination network that have a lower RD than the FD of the Successor path are guaranteed to be loop-free and are referred to as Feasible Successor (FS) routes. These routes are placed into the IP routing table.TrueFalseQuestion 9 of 18 10. ___ is used by EIGRP to ensure that Update, Query, and Reply packets are sent reliably.HellosDUALReliable Transport Protocol (RTP)AcknowledgementsQuestion 10 of 18 11. EIGRP is an open standard protocol and can be used on any vendors routers.FalseTrueQuestion 11 of 18 12. By default, EIGRP automatically summarises at classful boundaries and creates a summary route pointing to the Null0 interface.FalseTrueQuestion 12 of 18 13. The primary use of the EIGRP router ID (RID) is to?help with metric calculation.secure routing updates.verify routing updates.prevent routing loops.Question 13 of 18 14. The below message is printed on your console session. What does it mean? *Mar 2 22:12:46.589 CST: IP-EIGRP(Default-IP-Routing-Table:1): Neighbor 150.1.1.2not on common subnet for FastEthernet0/0One of the neighbours has been put in a different subnet so a neighbor relationship cannot form.One of the neighbours has been put in a different subnet but a neighbor relationship can still form.The router ID for the neighbor is on the wrong subnet.Question 14 of 18 15. Two routers are connected using EIGRP. One is in AS100 and the other is in AS200. They can both exchange routing updates.FalseTrueQuestion 15 of 18 16. You have the below networks on your router: Loopback0—IP Address 10.0.0.1/24 Loopback1—IP Address 10.1.1.1/24 Loopback2—IP Address 10.2.2.1/24 Loopback3—IP Address 10.3.3.1/24You configure the below networks. What will the result be? R1(config)#router eigrp 150 R1(config-router)#network 10.1.1.0 R1(config-router)#network 10.3.3.0 R1(config-router)#exitIf you add the 'no auto-summary' command then all networks will be advertisedIf you add the 'no auto-summary' command then only the configured networks will be advertisedOnly the networks 10.1.1.0 and 10.3.3.0 will be advertised.All 10.0.0.0 networks will be advertisedQuestion 16 of 18 17. RTP uses both Multicast and Unicast packets.TrueFalseQuestion 17 of 18 18. Enhanced IGRP Hello packets are sent to the Link Local Multicast group address _______.224.0.0.102224.0.0.2224.0.0.10224.0.0.1Question 18 of 18 Loading...