Day 57 Back to Exams Page 1. Each EtherChannel can consist of how many ports in total?248Platform dependant.UnlimitedQuestion 1 of 27 2. HSRP allows ____ physical gateways that are configured as part of the same HSRP group to share the same virtual gateway address.eightfoursixtwo Question 2 of 27 3. By default, HSRP messages are sent with the plain text key string “cisco” as a simple method to authenticate HSRP peers.TrueFalseQuestion 3 of 27 4. What does the * indicate in the output below? R2#show ip route 172.16.100.0 255.255.255.0Routing entry for 172.16.100.0/24Known via “eigrp 150”, distance 90, metric 2172416, type internalRedistributing via eigrp 150Last update from 150.1.1.1 on Serial0/0, 00:01:55 agoRouting Descriptor Blocks:* 150.1.1.1, from 150.1.1.1, 00:01:55 ago, via Serial0/0Route metric is 2172416, traffic share count is 1Total delay is 20100 microseconds, minimum bandwidth is 1544 KbitReliability 255/255, minimumThe asterisk (*) points to the interface with the best metric if there is more than one route available.The asterisk (*) points to the first route learned by EIGRP.The asterisk (*) points to the interface where traffic shaping has been configured.The asterisk (*) points to the interface over which the next packet is sent.Question 4 of 27 5. What does the below HSRP virtual MAC address tell you? Gateway-1#show standby[Trunkated]Standby router is 192.168.1.2, priority 100 (expires in 9.019 sec)Priority 105 (configured 105)IP redundancy name is “hsrp-Fa0/0-1” (default)State is Active2 state changes, last state change 00:09:45Virtual IP address is 172.16.1.254Active virtual MAC address is 0000.0c07.ac02Local virtual MAC address is 0000.0c07.ac02 (v1 default)Hello time 3 sec, hold time 10 secNext hello sent in 2.423 secsPreemption disabledActive router is localThis is using HSRP v2The other router is using preemptionThis is HSRP group 7This is HSRP group 2Question 5 of 27 6. The STP timers below have which values: Hello/Forward Delay/Max Age5/10/202/15/2015/2/201/10/20Question 6 of 27 7. BPDU Guard disables STP on an interface.TrueFalseQuestion 7 of 27 8. Root Guard prevents a ____ port from becoming a _____ port?root/designateddesignated/rootblocking/rootroot/forwardingQuestion 8 of 27 9. HSRP routers exchange the following three types of messages:CoupPreemptResignHelloQuestion 9 of 27 10. In order to set a switch to become the STP root you need to set it's priority to the highest possible value.TrueFalseQuestion 10 of 27 11. RSTP port roles include?BackupDisabledListeningDesignatedAlternateRootQuestion 11 of 27 12. STP BPDUs are sent ever __ seconds.41062Question 12 of 27 13. ________ BPDUs are sent by LAN switches and are used to communicate and compute the Spanning Tree topology.ElectionPreemptionConfigurationNominationQuestion 13 of 27 14. To copy the config from DRAM to NVRAM you issue which command?copy tftp flashcopy run startcopy flash tftpcopy start runQuestion 14 of 27 15. HSRP routers exchange the following three types of messages:Resign messagesInterruptPreemptHello messagesCoup messagesQuestion 15 of 27 16. When a switch port is configured in passive mode, it will negotiate with an LACP channel only if it receives another LACP packet.FalseTrueQuestion 16 of 27 17. The STP port value for a 100Mbps interface is?19100102Question 17 of 27 18. When determining the RID, EIGRP will select the _____ IP address that is configured on the router.highestlowestQuestion 18 of 27 19. HSRP version 1 routers communicate by sending messages to Multicast group address ____ using UDP port ____.224.0.0.2/1986224.0.0.2/1985224.0.0.10/19224.0.0.10/1985Question 19 of 27 20. Enhanced IGRP Hello packets are sent to the Link Local Multicast group address _______.224.0.0.10225.0.0.10223.0.0.10224.0.0.11Question 20 of 27 21. STP uses the exchange of BPDUs to determine the network topology, which is determined by the following three variables:The first switch to send a BPDUThe path cost to the Root Bridge associated with each switch portThe unique MAC address (switch identifier) that is associated with each switchThe port identifier (MAC address of the port) associated with each switch portQuestion 21 of 27 22. You want a switch to become the root should the primary switch fail. The primary switch is set to 0. Which value do you enter on the secondary switch?10409610241Question 22 of 27 23. Two HSRP gateways are configured with priorities 100 and the other is 110. Which one will be elected primary gateway?None10090Question 23 of 27 24. Connected interfaces using PAgP modes Desirable on one side and Auto on the other will form an EtherChannel.FalseTrueQuestion 24 of 27 25. Which of the below are true for the EIGRP K values?K2=K4=K5=0K1=K3=0K1=K3=1K2=K4=K5=0Question 25 of 27 26. Which of the below commands will configure a passive interface for Loopback 0?R1(config-router)#passive-interface Loopback0R1(config-if)#passive-interface R1(config)#passive-interface Loopback0R1(config-if)#passive-interface Loopback0Question 26 of 27 27. Two connected interfaces using PAgP Auto mode will form an EtherChannel.TrueFalseQuestion 27 of 27 Loading...